AVIATION TRIVIA 
   Home      de Havilland Beaver
 
 
 
 

RC Beaver
(Radio Control Airplanes Beaver)

You Tube - RC Beaver


Specifications

    Primary Function:
    Seats:
    Engine:
    Power:
    Length:
    Wingspan:
    Weight Empty:
    Max. Weight:
    Fuel:
    Payload:
    Cruise Speed:
    Max. Speed:
    Climb Rate:
    Ceiling:
    Range:
    First Flight:
transport
four
P&W R-985
450 h.p.
30 ft. 4 in.
48 ft.
2,850 lbs.
5,211 lbs.
141 U.S. gals.
2,100 lbs.
130 mph
160 mph
1,020 fpm
18,000 feet
470 miles
8/16/47







RC Beaver
Click on the RC Beaver to hear the wav sound.



RC Beaver

The rc Beaver pictured just above from HobbyKing has a 71 in. wingspan and is 47 in. long.  Included with the ARF are flaps. Weight is around 6 lbs.

HobbyKing has a smaller rc Beaver with a wingspan of 40 in. and length of 28 in.  It is of all wood construction.

The Beaver is a high wing monoplane powered by a single radial engine that was produced to take off and land in short distances while equipped with heavy loads and optional floats. The design can withstand the rigors of sub zero temperatures and less than perfect landings on unimproved air strips, ice, snow, or choppy waters.



RC Beaver

The rc Beaver from NitroPlanes comes as an all-wood kit. It has a 71 in. wingspan and needs a 1,000 kV motor for power.

The Beaver first flew in 1947 with production continuing through 1967. A total of 1,692 were produced of which some 718 were sold throughout the world. The remainder were purchased by the United States government for use by their army, navy, and air forces. The airplane was even used by the U.S. as a utility transport over Korea during the Korean War. Several hundred Beavers continue to fly today.



RC Beaver

Flyzone's rc Beaver has a wingspan of 59 1/2 in., length of 38 1/2 in., and includes a motor, controller, servos, and receiver.  Weight is around 3 lbs.

The Beaver has a one ton capacity, even when equipped with floats. Its rear doors are large enough for easy loading and unloading of 55 gallon drums. It is a true workhorse.



RC Beaver

The rc Beaver from Ever Soaring Models - ESM has a 95 in. wingspan and is 61 in. long. The ARF has a glass fibre fuselage and all wood wings with working flaps. It can be propelled by 35 cc to 56 cc engines and should weigh about 17 lbs. all-up.

Three fuselage fuel tanks, with a total capacity of some 95 gals., are located in the bottom front of the airplane. This makes for easy refueling. The wing tanks of the Beaver hold an additional 46 gals. of fuel. When flying the Beaver, extra attention must be paid as fuel is consumed in order to keep the airplane properly balanced.



RC Beaver

E-flite's rc Beaver is made from balsa and ply.  Its wingspan is 68 in., length is 43 in. and weight is about 5 1/2 lbs.

Cold starting the radial engine is a bit more involved than with a conventional engine. To prevent locking that can result from the pooling of oil, the propeller should be hand turned several times. Once started, the engine should be run at idle for twelve or so minutes to make sure its oil supply and total mass is properly warmed.



RC Beaver

The GWS rc has a 40 in. wingspan and 27 in. length. It weighs only 13 oz. ready to fly. Included is a geared 370 motor.

Throttle management during take off acceleration is necessary so as not to build up excessive manifold pressure. This is a relatively large, heavy, single engine airplane, and while it will not get into the air as quickly as a lighter airplane, its short take off, especially when fully loaded, is impressive. The flaps of the Beaver operate in conjunction with its ailerons to help produce exceptional lift.



RC Beaver

The rc Beaver from Texas RC Planes has a 118 in. wingspan and is 78 in. long. It comes with optional floats. A 6.10 engine is recommended to power it.

Although the airplane has a rather large side profile, cross wind landings and take offs are not difficult for experienced pilots. The controls are not heavy as one would expect, and are pleasant to handle. However, no one could ever say that the Beaver is quick to respond to control inputs.



RC Beaver

The rc Beaver from MR Aerodesigs comes as a kit or plans. It has a wingspan of 104 in. with a length of 65.5 in. Recommended is a 38 cc engine.  Weight is from 19 to 21 lbs.

The radial engine of the Beaver and overall bulk produces lots of drag. Landings are made with the nose down and extra attention paid to speed on final. Bringing the nose up, even under full power, will just make the airplane mush. To regain altitude, the stick must be moved forward. So long as the limitations of the airplane are observed, landings are easy.



RC Beaver

The rc Beaver pictured just above from Easy Build Models comes in a kit. It uses three channel control and an Speed 500 type motor for power.  Wingspan is 57 in.

In 1964 a turbine engine Beaver was produced. Its engine had about 125 more h.p. than the standard radial engine and the airplane was some two feet longer. However, only 60 were built.

A rc Beaver has been made from an 18 in. wingspan Dumas rubber powered model. Conversion is to electric motor power.

The VQ Models rc Beaver has a 63 in. wingspan and comes as ARF. You have a choice of power from up to 870 Wt. electric motors, .52 two cycle or .70 four cycle engines. Weight is about 7 lbs.

Slip Stream has a rc Beaver that comes ARF. Its wingspan is 87 in. and length 62 in. It needs a 1.8 engine for power.

Complete-A-Pac (CAP) makes a rc Beaver that comes as a kit that has a six foot wingspan. Balsa and plywood are used in its construction. Power can come from a .40 to .60 four cycle engine.

The AMA Plans Service has plans for a rc Beaver with a 72 in. wingspan for engine power. The plan comes from the Oct. 1989 issue of Model Airplane News. Plan number is 26657.

Flying Styro has a rc Beaver. It has a wingspan of 43 in. and a length of 28 in. Both floats and wheels come with it. Weight is around 1 lb. 4 oz.

Kondor Model Products - KMP has a rc Beaver available with or without floats.  It has a wingspan of 96 in., weight around 16 lbs. ready to fly w/o floats, and uses 1.6 to 1.8 four cycle engines.

RC Universe shows a rc Beaver kit from Model Fly. It has a 62 in. wingspan and is 45 in. long. Using a .46 2C engine and with floats, it weighs in at around 8.5 lbs.

Ikon N'wst has a rc Beaver in a kit. Wingspan is 96 in. and weight is around ll lbs. You will need a 1.20 four cycle engine for power.

Air Age Store.com has plans for the rc Beaver. It has a 70 in. wingspan and a 46 in. length. You can use from .40 to .50 2C engines for power.

On You Tube wildcat214 posted a video of his rc Beaver.

At You Tube dvdcort posted a video of his rc Beaver float plane.

There are several threads at RCGroups about conversions to a rc Beaver of a 30 in. Dumas model. DW's conversion weighs just 8 oz. and uses a geared GWS motor for great flying.

Tracon of RCGroups started a thread about a rc Beaver.

At RCGroups warhead_71 posted a video and description of his rc Beaver.

Coastwatcher of RCGroups started a thread about improvements that he made to his rc Beaver.

At RCGroups peterpont was looking for a rc Beaver.

Michael Heer of RCGroups wrote a column about converting a rc Beaver to a float plane.

Mike Buzzeo of RCUniverse wrote all about his rc Beaver.

At RCUniverse airhead was contemplating building a rc Beaver from plans or a kit.

At RCUniverse noworknguy was looking for a rc Beaver.

At RCUniverse butlern started a thread about the assembly of his rc Beaver.

At WattFlyer tiger408 was looking for rc Beaver plans.

At WattFlyer denisscottallen inquired about a rc Beaver in a kit.

At WattFlyer jupiter1 asked if anyone has experience with a particular rc Beaver kit.

At WattFlyer jcblough was seeking suggestions about propelling his rc Beaver.

Tracon of WattFlyer posted photos and a description of his rc Beaver.

Email us.